Images are representations only.
Description
- Input for RTD, TC, Ohm, potentiometer, mA and V
- 2-wire supply > 16 V
- FM-approved for installation in Div. 2
- Output for current, voltage and 2 relays
- Universal AC or DC supply
- When 4116 is used in combination with the 45xx display / programming units, all operational parameters can be modified to suit any application. As the 4116 is designed with electronic hardware switches, it is not necessary to open the device for setting of DIP-switches.
- A green / red front LED indicates normal operation and malfunction. A yellow LED is ON for each active output relay.
- Continuous check of vital stored data for safety reasons.
- 4-port 2.3 kVAC galvanic isolation.
Specifications
Specifications
Brand
Accuracy
- 0.1 % of Selected Range
Approvals & Certifications
- DNV Marine Standard F. Certificate No. 2.4
- EAC TR CU 020/2011
- EMC 2014/30/EU
- FM 3025177
- Hardware Assessed for use in SIL Application
- IEC 60068-2-6: 2007
- LVD 2014/35/EU
- UL 508
Calibration
- 20° to 28° C (68° to 82° F)
Circuit Protection
- < 15 ohms - Short Circuit Detection
Dimensions
- 109 x 23.5 x 116 / 131 mm
Display
- Green/Red LED Front & Yellow LED is ON for Each Active Output Relay
Electromagnetic Rating
- EMC - 2014/30/EU
Environmental Protection
- IP20
Humidity
- < 95 % Relative Humidity, Non-Condensing
Input
- 0 to 10,000 ohms - Linear Resistance
- 0 to 12 Vdc
- 0-20 mA
- 10 to 100 kiloohms - Potentiometer Input
- 4-20 mA & 0-20 mA - Programmable Measurement Range
- RTD Typical - Pt10, Pt20, Pt50, Pt100, Pt200, Pt250, Pt300, Pt400, Pt500, Pt1000 Ni50, Ni100, Ni120, Ni1000, Cu10, Cu20, Cu50, Cu100
- Thermocouple Typical - B, E, J, K, L, N, R, S, T, U, W3, W5, LR
Input Power
- 0-20 mA - 2-Wire Auxiliary Supply
- 25 to 16 Vdc - 2-Wire Auxiliary Supply
- 400 mA SB / 250 Vac - Fuse
Isolation
- 2.3 kVac/250 Vac - Isolation Voltage, Test/Working & Galvanic Isolation
Load Limit
- ≤ 0.01 % of Span/100 ohms
Output
- ≤ 28 mA - Current Limit
- 0-10 Vdc - Voltage Output
- 0-20 / 4-20 / 20-0 & 20-4 mA - Current Output (Programmable Signal Range)
- 0-20 mA - Current Output
- 23 mA / 3.5 mA - NAMUR NE 43 Upscale / Downscale
Output Load
- ≤ 800 ohms at Current Output
- ≥ 500 kOhms - Voltage Output
Port
- 4-Ports
Power Requirement
- ≤ 2.5 W
Relay Output
- 2 Relay Contacts
- 250 VRMS - Voltage
- 500 VA - AC Power
Resistance
- Nominal 20 ohms + PTC 50 ohms - Input Resistance
Response Time
- ≤ 1 seconds - Temperature Input
- ≤ 400 milliseconds - mA/V Input
Sensor Input
- 0.2 mA
Sensor, Probe Connection
- 2-Wire
Storage Temperature
- -20° to 85° C (-4° to 185° F)
Supply Voltage
- 19.2-300 Vdc
- 21.6-253 Vac, 50/60 Hz
Switch Type
- DIP Switches
Temperature Range
- -20° to 60° C (-4° to 140° F)
Vibration
- ± 0.7 G, 13.2 to 100 Hz
- ± 1 mm - 2 to 13.2 Hz
Wiring
- 1 x 2.5 mm² - Standard Wire
Applications
Applications
- Linearized, electronic temperature measurement with RTD or TC sensor.
- Conversion of linear resistance variation to a standard analog current / voltage signal, i.e. from solenoids and butterfly valves or linear movements with attached potentiometer.
- Power supply and signal isolator for 2-wire transmitters.
- Process control with 2 pairs of potential-free relay contacts and analog output.
- Galvanic separation of analog signals and measurement of floating signals.
- The 4116 is designed according to strict safety requirements and is therefore suitable for application in SIL 2 installations.
- Suitable for the use in systems up to Performance Level “d” according to ISO-13849.
